info@graphlertech.com+91 962-951-4005Coimbatore, Tamil Nadu, India
Upload 3D files Order tracking
Request a Quote
Industries · Industrial Automation & Robotics

Precision Manufacturing & Engineering Solutions for Industrial Automation & Robotics

Graphler delivers mission-critical mechanical components, multi-axis robotic arm linkages, custom end-of-arm tooling (EOAT), automated guided vehicle (AGV) chassis, and precision gearboxes with tolerances as tight as ±0.0002 inches.

Accepted CAD formatsSTLSTEPIGESZIP

Robotic Kinematic LinkagesCustom End-of-Arm Tooling (EOAT)Sub-Micron Bearing & Gear Seats
  • Robotic Kinematic LinkagesLightweight, high-stiffness aluminium and alloy steel arms machined on 4-axis and 5-axis VMC centers.
  • Custom End-of-Arm Tooling (EOAT)Pneumatic, vacuum, and mechanical gripper assemblies with integrated weight-saving pockets.
  • Sub-Micron Bearing & Gear SeatsBoring and turning tolerances held down to ±0.0002 inches to eliminate backlash and mechanical hysteresis.
  • Simulation & FEA BackedFinite Element Analysis (FEA) to maximize stiffness-to-weight ratio and simulate dynamic cyclic loading.
  • ISO 9001 Compliant QualityFull CMM dimensional inspection, material test certifications, and complete batch traceability.

High-Speed Dynamic Loading & Zero-Backlash Rigidity Requirements

Industrial automation systems, collaborative robots (cobots), and high-speed pick-and-place mechanisms operate under continuous multi-axis accelerations, dynamic inertial loads, and high-frequency vibrational stress. Any joint flexure, dimensional deviation, or bearing seat eccentricity translates directly into positioning errors and premature actuator failure. Graphler combines multi-axis CNC machining, precision sheet metal fabrication, and Finite Element Analysis (FEA) to manufacture lightweight, structurally rigid components that maintain kinematic accuracy over millions of continuous duty cycles.

Core Manufacturing Solutions for Automation & Robotics Subsystems

  • 01

    Robotic Arm Structures & Joint Housings

    • Multi-Axis CNC Milling

      Machining structural robot arms, swivel joints, and motor mounting housings from 6061-T6 and 7075-T6 billets on 4-axis and 5-axis VMC setups.

    • Sub-Micron Bearing Seats

      Internal boring and turning held to ±0.0002 inches to ensure perfect bearing alignment and eliminate rotational runout.

    • Weight-Reduction Pockets

      DFM-optimized pocketing to decrease rotational inertia and lower actuator power consumption.

  • 02

    End-of-Arm Tooling (EOAT) & Gripper Mechanisms

    • Custom Gripper Fingers & Jaws

      Precision-machined aluminium, stainless steel, and hardened tool steel gripper jaws with custom contouring.

    • Pneumatic & Vacuum Manifolds

      Multi-port manifolds machined with leak-tight internal ports and integrated quick-connect pneumatic fittings.

    • Polymer & Elastomeric Inserts

      Vacuum-injected polyurethane and silicone gripping pads to prevent scratching delicate workpieces.

  • 03

    AGV / AMR Chassis & Automation Enclosures

    • Laser Cut & CNC Formed Frames

      Fiber laser cutting and CNC press brake bending of high-yield steel and aluminium chassis for autonomous mobile robots.

    • Certified Structural Welding

      MIG and TIG welding of modular base frames to ensure shock resistance against rough industrial flooring.

    • Powder Coated Electrical Consoles

      Custom sheet metal NEMA/IP-rated control cabinets with anti-corrosion electrostatic powder coating.

Engineered Materials for High Stiffness, Low Inertia & Wear Resistance

We machine, cast, and fabricate high-performance engineering alloys tailored for dynamic acceleration and wear resistance:

Al01

Robotic Linkages & Arms

Aluminium 6061-T6, 7075-T6

High strength-to-weight ratio to minimize rotational inertia and cycle times

St02

Actuator Housings & Shafts

Alloy Steel (4140, EN19, EN24)

High fatigue limits and torsional strength under reversing torque loads

SS03

Grippers & Wear Slides

Tool Steels (D2, O1), Stainless (304, 316)

Surface hardness up to 60 HRC to resist friction, galling, and abrasive wear

St04

AGV / AMR Structural Frames

Structural Steel (IS 2062, A36), 5052-H32

High dynamic impact resistance and vibration damping

Al05

Pneumatic & Valve Manifolds

Hardcoat Anodized Aluminium 6061

Corrosion resistance, dielectric insulation, and scratch protection

Systematic 6-Step Engineering & Production Workflow

  1. CAD upload & review

    Upload 3D CAD files for rapid quoting supported by a two-stage technical feasibility review.

  2. DFM & engineering review

    Dedicated engineering DFM review to finalize tolerances, kinematic fits, and material selections.

  3. Controlled manufacturing

    Precision manufacturing via multi-axis VMC/HMC milling, CNC turning, and sheet metal fabrication.

  4. Post-processing

    Integrated post-processing including Type III hardcoat anodizing, chemical blackening, and grinding.

  5. Quality inspection

    Comprehensive dimensional CMM inspection and structural joint verification.

  6. Packaging & logistics

    Export-compliant protective packaging and worldwide shipping with real-time order tracking.

Integrated Simulation (FEA/CFD) & ISO 9001 Quality Control

Select a checkpoint to see how it is verified.

FEA Dynamic Simulation

Modal and harmonic vibration analysis to identify natural frequencies and avoid robotic resonance.

Design for Manufacturability (DFM)

Optimizing tool reach, corner radiuses, and wall thicknesses to eliminate multi-setup machining costs.

CMM Geometric Tolerancing

Verifying positional accuracy, perpendicularity, and bearing concentricity against GD&T drawings.

Full Traceability

Supplying raw material test certificates (MTRs) and batch inspection documentation with every shipment.

  • FEA Dynamic Simulation

    Modal and harmonic vibration analysis to identify natural frequencies and avoid robotic resonance.

  • Design for Manufacturability (DFM)

    Optimizing tool reach, corner radiuses, and wall thicknesses to eliminate multi-setup machining costs.

  • CMM Geometric Tolerancing

    Verifying positional accuracy, perpendicularity, and bearing concentricity against GD&T drawings.

  • Full Traceability

    Supplying raw material test certificates (MTRs) and batch inspection documentation with every shipment.

Technical questions: Industrial Automation & Robotics

Straight answers from the engineers who run the work.

Ask a technical question
What tolerances can Graphler achieve for robotic joint housings and gear seats?

We achieve critical dimensional tolerances as tight as ±0.0002 inches (±0.005 mm) on CNC machining centers, ensuring precision bearing fits and zero-backlash assembly.

Can Graphler assist with weight reduction and FEA analysis for robotic end-effectors?

Yes. Our engineering team integrates Finite Element Analysis (FEA) and DFM optimization to remove unnecessary mass from EOAT assemblies without sacrificing mechanical stiffness.

What CAD formats are accepted for an automation manufacturing quote?

We accept 3D CAD models in STEP (.stp), IGES (.igs), STL (.stl), and compressed (.ZIP) archives.

Start an Industrial Automation & Robotics project

Upload your 3D CAD model and drawing. An engineer reviews feasibility, tolerances and material certification before we quote.